- 30-day returns
- Fast shipping
- Secure payments
- Over 300,000 products
age_group:
18+
category:
Mops
country_of_origin:
USA
gender:
Unisex
manufacturer:
Specialty Optical Systems / SOS Cleanroom
mpn:
TX7102
sub_brand:
ITW TEXWIPE
type:
Mops
Product Description
Texwipe TX7102 ClipperMop™ Cleanroom Mop Kit — 7" x 4" Head Assembly with Telescoping Handle (Uses 9" x 9" Wipers)
TX7102 is a cleanroom-compatible mopping system for flat vertical and horizontal surfaces where technicians need consistent wipe-and-mop execution without introducing new mop-cover materials into a validated program. The 7" x 4" low-profile, swivel head is designed to clamp standard 9" x 9" cleanroom wipers using non-abrasive clips, helping teams standardize one wiper family for both surface wiping and mopping routes.
For over 35 years, SOS and Texwipe have been close partners, and SOSCleanroom is the authorized Master Distributor of ITW Texwipe for the United States market. That relationship matters in critical environments: it supports continuity of supply, stable product lineage, and faster access to manufacturer documentation for qualification, change control, and audit readiness.
For over 35 years, SOS and Texwipe have been close partners, and SOSCleanroom is the authorized Master Distributor of ITW Texwipe for the United States market. That relationship matters in critical environments: it supports continuity of supply, stable product lineage, and faster access to manufacturer documentation for qualification, change control, and audit readiness.
Published configuration (TX7102)
- System type: ClipperMop™ cleanroom mop kit (head assembly + telescoping handle)
- Mop head size: 7" x 4" (18 cm x 10 cm)
- Wiper format used on head: Standard 9" x 9" cleanroom wipers (dry, pre-wetted, sterile or non-sterile per published guidance)
- Mop head construction (as published): Celcon® thermoplastic head with four polyethylene clips tethered with nylon fasteners
- Pad layer (as published): Flexible polyester foam pad to help the loaded wiper conform to uneven surfaces
- Handle extension range (as published): 2'5" to 4'5" (also shown as 29" to 53")
- Packaging (as published): 1 mop kit per case; double-bagged with bag-within-a-bag cleanroom packaging (supports inner-bag wipe-down before introduction)
- Sterilization compatibility (as published): Gamma irradiation, chemicals, vaporized hydrogen peroxide (VHP) or ethylene oxide (EO)
- Cleanroom environment (as published): ISO Class 3–7 (also shown as ISO Class 3–8 in some legacy documentation); EU Grade A–D; Class 1–10,000 (also shown as Class 1–100,000 in some legacy documentation)
Configuration note for QA change control
Published handle construction varies by document generation. One widely used legacy datasheet specifies a powder-coated steel telescoping handle; newer ClipperMop series documentation lists a telescoping fiberglass handle model (TX7122). If your program is sensitive to handle composition (particles, corrosion, chemical exposure, or ESD considerations), confirm the current shipped configuration under your site change-control process before standardizing.
How the ClipperMop system supports critical cleaning routes
- Standardize the contact layer: The same validated cleanroom wiper family can be used for benches/equipment and for mopping, reducing the number of materials your site must qualify and inventory.
- Clip-based loading: Non-abrasive clips secure one or multiple wipers to the head. Frequent wiper replacement supports strict cleaning protocols and reduces re-deposition risk.
- Low-profile access: The swivel head and compact footprint help reach under equipment edges, around carts, and into confined spaces such as antechambers, isolator exteriors, and gowning areas.
- Solution application/removal: Published use includes applying and removing cleaning solutions and disinfectants. Route quality is driven by wet-load control, pass pattern discipline, and change-out rules.
Practical cleanroom use guidance (technicians and engineers)
- Define a wet-load target: Over-wetting causes streaking/filming and can spread residues into seams and transitions. Standardize wringing method, dwell time, and solution volume per route segment.
- Use repeatable pass patterns: Overlap passes and maintain consistent direction. Random scrubbing increases re-deposition and makes deviations harder to investigate.
- Wiper change-out is the control knob: Replace the loaded wiper at defined area/time limits and whenever you see streaking, visible loading, or loss of glide. Extending wiper life is a common root cause of residue carryover.
- Stage clean vs. used hardware: Once the route begins, treat the mop as a “dirty tool.” Keep used wipers and accessories segregated to avoid cross-contamination back into clean staging.
- Edge control: Avoid forcing wet wipers into door thresholds, drains, or floor seams where residues can accumulate. Use a defined detailing tool where your SOP requires it.
Process-control table (high-impact variables)
| Control point | What to standardize | Failure symptom if missed |
|---|---|---|
| Wiper loading method | Single vs. multiple wipers; fold pattern; clip engagement check | Slippage, uneven contact, missed coverage, edge drag |
| Wet-load and wring | Pickup volume, wring force, dwell time before use | Streaking/filming, chemical residue, puddling |
| Route design | Direction, overlap, boundary rules (doors, thresholds) | Re-contamination streaks, inconsistent results between shifts |
| Change-out limits | Max area/time per loaded wiper; hard-stop triggers | Residue carryover, particle re-deposition, “sticky” floor feel |
Published wiper recommendations (common validation pairings)
Below is a published pairing table intended to help teams select compatible Texwipe wipers that are commonly validated in controlled environments for wipe-and-mop workflows.
| Category | Texwipe wiper | Product name (as published) | Notes for TX7102 workflows |
|---|---|---|---|
| Dry wipers | TX1010 | Vectra® Alpha® 10 | Common for low-residue wipe/mop where consistency is prioritized |
| Dry wipers | TX1012 | Alpha® 10 | Frequent pairing for controlled wiping and mopping routes |
| Dry wipers | TX1050 | Vectra® AlphaSorb® 10 | Higher absorbency use cases; qualify residue and dry-down time |
| Dry wipers | TX1052 | AlphaSorb® 10 | Absorbency-driven workflows; validate change-out interval |
| Dry wipers | TX1060 | Vectra® HoneyComb® 10 | Textured pickup profiles; qualify for fiber/particle sensitivity |
| Dry wipers | TX1009 | AlphaWipe® | Broad-use pairing for wipe-and-mop standardization |
| Dry wipers | TX1013 | AlphaWipe® | Alternative AlphaWipe configuration; validate against SOP targets |
| Dry wipers | TX2412 | AlphaSorb® HC | High-absorbency cleanup; control residue and contact time |
| Dry wipers | TX3215 | SterileWipe™ AS 10 | Sterile workflow pairing where sterile wipers are required |
| Dry wipers | TX3210 | SterileWipe™ HS II | Sterile route control; validate packaging transfer method |
| Dry wipers | TX609 | TechniCloth® | Common facility-grade pairing; align to room grade |
| Dry wipers | TX612 | TechniCloth® | Alternative TechniCloth configuration; validate vs. SOP |
| Pre-wetted (IPA blends) | TX1084 | QuanSat™ with Vectra® QuanTex™ | Published with 70% IPA; control dry-down and residue risk |
| Pre-wetted (IPA blends) | TX8513 | QuanSat™ with Vectra® Quantum® 100 | Published with 70% IPA; control wet-load consistency |
| Pre-wetted (IPA blends) | TX1039 | AlphaSat® with AlphaWipe® | Published with 70% IPA; common for wipe-and-mop standardization |
| Pre-wetted (IPA blends) | TX1041 | TechniSat® | Published with 70% IPA; align to room grade and residue tolerance |
| Pre-wetted (IPA blends) | TX1065 | TechniSat® | Published with 70% IPA; validate for streaking/film potential |
| Pre-wetted (IPA blends) | TX1051 | PolySat® | Published with 70% IPA; confirm material compatibility with chemistry set |
| Pre-wetted (IPA blends) | TX3285 | Sterile AlphaSat® 10 | Sterile pre-wetted pairing for aseptic programs |
| Pre-wetted (IPA blends) | TX3252 | Sterile AlphaSat® with AlphaSorb® HC | Sterile, higher absorbency workflows; validate residue and dry time |
| Pre-wetted (IPA blends) | TX3214 | Sterile TechniSat® | Sterile pre-wetted pairing; validate transfer method into room |
| Pre-wetted (IPA blends) | TX3213 | SterilePolySat® | Sterile polymer wiper pairing; align with chemistry compatibility |
| Pre-wetted (IPA blends) | TX1057 | AlphaSat® with Vectra® AlphaSorb® 10 | Published with 10% IPA; qualify for residue-sensitive programs |
| Pre-wetted (IPA blends) | TX1046 | AlphaSat® with Vectra® Alpha® 10 | Published with 6% IPA; supports lighter solvent load where required |
| Pre-wetted (IPA blends) | TX1086 | QuanSat™ with Vectra® QuanTex™ | Published with 6% IPA; validate against your disinfectant rotation |
| Pre-wetted (IPA blends) | TX8488 | TechniSat® | Published with 6% IPA; qualify for streaking/film risk |
Common failure modes
- Streaking / film residue: Typically from uncontrolled wet load, chemistry incompatibility with floor finish, or extending wiper change-out too long. Prevent with wet-load targets, defined wring method, and hard-stop change-out rules.
- Residue carryover between zones: Triggered by poor staging discipline (clean vs. used) or route shortcuts. Prevent with zone-separated carts, labeled buckets, and one-direction route logic.
- Particle re-deposition: Caused by reusing loaded wipers or dragging a drying wiper across previously cleaned areas. Prevent with overlap discipline and frequent wiper replacement.
- Clip loading errors: Partial clip engagement or uneven folds can cause edge drag, missed coverage, and slippage. Prevent with a standardized fold pattern and a quick “four-clip check” before entering the room.
- Corner/threshold contamination: Forcing wet wipers into seams can trap residues. Prevent with edge control and a defined detailing tool for transitions.
Storage and handling best practices
- Keep the kit in original cleanroom packaging until introduction; leverage bag-within-a-bag wipe-down practices if your SOP allows.
- Stage clean kits, clean wipers, and prepared solutions in a designated clean area; segregate used wipers immediately after the route begins.
- Inspect head edges, clips, and fasteners routinely for embedded debris, damage, or looseness that could compromise coverage or introduce contaminants.
- Store dry and protected; avoid placing heavy items on the head assembly where deformation can change contact pressure and streak behavior.
Documentation
SOS-hosted Texwipe datasheet (DS-7102, Effective: December 2009): Click Here
Texwipe manufacturer Technical Data Sheet (ClipperMop™ Series, US-TDS-058 Rev. 11/21): Click Here
Texwipe manufacturer page (TX7102): Click Here
If you have any questions please email us at Sales@SOSsupply.com or give us a call at (214)340-8574.
Check out our AI ChatBot powered by SOSCleanroom data libraries - give it a try!
THIS IS NEW FOR 2026!
Last updated: January 9, 2026
© 2026 SOS Supply. All rights reserved.